Difference between revisions of "Hardware studies specific"

From Wiki at Neela Nurseries
Jump to: navigation, search
m (New section "Zephyr, ncs, and project files to review".)
m (Starting section on at_cmd_socket_thread.)
Line 219: Line 219:
 
<!-- comentario -->
 
<!-- comentario -->
  
== Files To Review ==
+
== [[#top|^}] Files To Review ==
  
 
The following files are from Zephyr, ncs, and or project `build` directory containing artifacts of the `west` directed, `ninja` based compilation:
 
The following files are from Zephyr, ncs, and or project `build` directory containing artifacts of the `west` directed, `ninja` based compilation:
Line 232: Line 232:
 
<!-- comentario -->
 
<!-- comentario -->
  
== Zephyr source i2c_nrfx_twim dot c ==
+
== [[#top|^}] Zephyr source i2c_nrfx_twim dot c ==
  
 
First reply to [https://devzone.nordicsemi.com/f/nordic-q-a/87549/i2c1-status-ok-configures-internal-pull-up-or-similar Devzone post 87549] points us to study some Zephyr sources in `~/projects/zephyr-based/zephyr/drivers/i2c`.
 
First reply to [https://devzone.nordicsemi.com/f/nordic-q-a/87549/i2c1-status-ok-configures-internal-pull-up-or-similar Devzone post 87549] points us to study some Zephyr sources in `~/projects/zephyr-based/zephyr/drivers/i2c`.
Line 242: Line 242:
  
 
*  https://github.com/nrfconnect/sdk-hal_nordic/blob/v1.5.2/nrfx/drivers/src/nrfx_twim.c#L315-L316
 
*  https://github.com/nrfconnect/sdk-hal_nordic/blob/v1.5.2/nrfx/drivers/src/nrfx_twim.c#L315-L316
 +
 +
 +
 +
<!-- comentario -->
 +
 +
== [[#top|^}] at_cmd_socket_thread ==
 +
 +
This work relates to study of a Zephyr reported thread named 'at_cmd_socket_thread'.
 +
 +
Code excerpt from './nrf/lib/at_cmd/at_cmd.c':
 +
 +
<pre>
 +
256                        if (errno == EHOSTDOWN) {
 +
257                                LOG_DBG("AT host is going down, sleeping");
 +
258                                atomic_set(&shutdown_mode, 1);
 +
259                                close(common_socket_fd);
 +
260                                nrf_modem_lib_shutdown_wait();
 +
261                                LOG_DBG("AT host available, "
 +
262                                        "starting the thread again");
 +
</pre>
  
  

Revision as of 22:52, 9 May 2022

Overview

This wiki article an effort to fully understand Zephyr RTOS facilities to fully configure, at start time and dynamically throughout run time I2C peripherals supported by Zephyr and given microcontroller Hardware Abstraction Layer (HAL) code.


^ 2022-05-02 Monday

Search for Zephyr's I2C peripheral configuration code . . .

ted@localhost:~/projects/zephyr-based/hardware-Stage1-firmware-aws-iot-stand-alone/build$ grep -nr i2c_configure ./*
./mcuboot/zephyr/include/generated/syscall_dispatch.c:668:uintptr_t z_mrsh_i2c_configure(uintptr_t arg1, uintptr_t arg2, uintptr_t arg3,
./mcuboot/zephyr/include/generated/syscall_dispatch.c:1412:	[K_SYSCALL_I2C_CONFIGURE] = z_mrsh_i2c_configure,
./mcuboot/zephyr/include/generated/syscalls/i2c.h:24:extern int z_impl_i2c_configure(const struct device * dev, uint32_t dev_config);
./mcuboot/zephyr/include/generated/syscalls/i2c.h:25:static inline int i2c_configure(const struct device * dev, uint32_t dev_config)
./mcuboot/zephyr/include/generated/syscalls/i2c.h:33:	return z_impl_i2c_configure(dev, dev_config);
./mcuboot/zephyr/include/generated/syscalls/i2c_configure_mrsh.c:10:extern int z_vrfy_i2c_configure(const struct device * dev, uint32_t dev_config);
./mcuboot/zephyr/include/generated/syscalls/i2c_configure_mrsh.c:11:uintptr_t z_mrsh_i2c_configure(uintptr_t arg0, uintptr_t arg1, uintptr_t arg2,
./mcuboot/zephyr/include/generated/syscalls/i2c_configure_mrsh.c:19:	int ret = z_vrfy_i2c_configure(*(const struct device **)&arg0, *(uint32_t*)&arg1)
./mcuboot/zephyr/misc/generated/syscalls.json:1159:            "int i2c_configure",
./spm/zephyr/include/generated/syscall_dispatch.c:668:uintptr_t z_mrsh_i2c_configure(uintptr_t arg1, uintptr_t arg2, uintptr_t arg3,
./spm/zephyr/include/generated/syscall_dispatch.c:1412:	[K_SYSCALL_I2C_CONFIGURE] = z_mrsh_i2c_configure,
./spm/zephyr/include/generated/syscalls/i2c.h:24:extern int z_impl_i2c_configure(const struct device * dev, uint32_t dev_config);
./spm/zephyr/include/generated/syscalls/i2c.h:25:static inline int i2c_configure(const struct device * dev, uint32_t dev_config)
./spm/zephyr/include/generated/syscalls/i2c.h:33:	return z_impl_i2c_configure(dev, dev_config);
./spm/zephyr/include/generated/syscalls/i2c_configure_mrsh.c:10:extern int z_vrfy_i2c_configure(const struct device * dev, uint32_t dev_config);
./spm/zephyr/include/generated/syscalls/i2c_configure_mrsh.c:11:uintptr_t z_mrsh_i2c_configure(uintptr_t arg0, uintptr_t arg1, uintptr_t arg2,
./spm/zephyr/include/generated/syscalls/i2c_configure_mrsh.c:19:	int ret = z_vrfy_i2c_configure(*(const struct device **)&arg0, *(uint32_t*)&arg1)
./spm/zephyr/misc/generated/syscalls.json:1159:            "int i2c_configure",
./zephyr/include/generated/syscall_dispatch.c:668:uintptr_t z_mrsh_i2c_configure(uintptr_t arg1, uintptr_t arg2, uintptr_t arg3,
./zephyr/include/generated/syscall_dispatch.c:1412:	[K_SYSCALL_I2C_CONFIGURE] = z_mrsh_i2c_configure,
./zephyr/include/generated/syscalls/i2c.h:24:extern int z_impl_i2c_configure(const struct device * dev, uint32_t dev_config);
./zephyr/include/generated/syscalls/i2c.h:25:static inline int i2c_configure(const struct device * dev, uint32_t dev_config)
./zephyr/include/generated/syscalls/i2c.h:33:	return z_impl_i2c_configure(dev, dev_config);
./zephyr/include/generated/syscalls/i2c_configure_mrsh.c:10:extern int z_vrfy_i2c_configure(const struct device * dev, uint32_t dev_config);
./zephyr/include/generated/syscalls/i2c_configure_mrsh.c:11:uintptr_t z_mrsh_i2c_configure(uintptr_t arg0, uintptr_t arg1, uintptr_t arg2,
./zephyr/include/generated/syscalls/i2c_configure_mrsh.c:19:	int ret = z_vrfy_i2c_configure(*(const struct device **)&arg0, *(uint32_t*)&arg1)
./zephyr/misc/generated/syscalls.json:1159:            "int i2c_configure",
ted@vibratsiya:~/projects/zephyr-based/hardware-Stage1-firmware-aws-iot-stand-alone/build$


- STEP - To identify first reference to routine i2c_configure() in Zephyr based project build artifacts.

An excerpt from file `ncs/project_root/build/zephyr/include/generated/syscalls/i2c.h:

 24 extern int z_impl_i2c_configure(const struct device * dev, uint32_t dev_config);
 25 static inline int i2c_configure(const struct device * dev, uint32_t dev_config)
 26 {
 27 #ifdef CONFIG_USERSPACE
 28         if (z_syscall_trap()) {
 29                 return (int) arch_syscall_invoke2(*(uintptr_t *)&dev, *(uintptr_t *)&dev_config, K_SYSCALL_I2C_CONFIGURE);
 30         }
 31 #endif
 32         compiler_barrier();
 33         return z_impl_i2c_configure(dev, dev_config);
 34 }


Search results:

ted@vibratsiya:~/projects/zephyr-based/hardware-Stage1-firmware-aws-iot-stand-alone/build$ grep -nr z_impl_i2c_configure ./*
./mcuboot/zephyr/include/generated/syscalls/i2c.h:24:extern int z_impl_i2c_configure(const struct device * dev, uint32_t dev_config);
./mcuboot/zephyr/include/generated/syscalls/i2c.h:33:	return z_impl_i2c_configure(dev, dev_config);
./spm/zephyr/include/generated/syscalls/i2c.h:24:extern int z_impl_i2c_configure(const struct device * dev, uint32_t dev_config);
./spm/zephyr/include/generated/syscalls/i2c.h:33:	return z_impl_i2c_configure(dev, dev_config);
./zephyr/include/generated/syscalls/i2c.h:24:extern int z_impl_i2c_configure(const struct device * dev, uint32_t dev_config);
./zephyr/include/generated/syscalls/i2c.h:33:	return z_impl_i2c_configure(dev, dev_config);

Hmm kind of dead ending here, no routine definitions found in either `zephyr` source tree nor `nrf` code projects. And `west build -t menuconfig` session shows CONFIG_USERSPACE=n.


- STEP - A search for CONFIG_PULL_UP symbol among Zephyr sources:

Subset of many results . . .

./boards/arm/nrf9160dk_nrf9160/nrf9160dk_nrf9160_common.dts:47:			gpios = <&gpio0 8 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>;
./boards/arm/nrf9160dk_nrf9160/nrf9160dk_nrf9160_common.dts:51:			gpios = <&gpio0 9 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>;
./boards/arm/nrf9160dk_nrf9160/nrf9160dk_nrf9160_common.dts:55:			gpios = <&gpio0 6 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>;
./boards/arm/nrf9160dk_nrf9160/nrf9160dk_nrf9160_common.dts:59:			gpios = <&gpio0 7 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>;
./boards/arm/nrf9160dk_nrf9160/nrf9160dk_nrf9160_common_0_14_0.dtsi:38:		int-gpios = <&gpio0 6 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>;


^ Search For I2C Configuration Source Code

  1 "nrf":"/home/ted/projects/zephyr-based/nrf":"/home/ted/projects/zephyr-based/nrf"
  2 "openthread":"/home/ted/projects/zephyr-based/modules/lib/openthread":"/home/ted/projects/zephyr-based/modules/lib/openthread/zephyr"
  3 "mcuboot":"/home/ted/projects/zephyr-based/bootloader/mcuboot":"${ZEPHYR_MCUBOOT_CMAKE_DIR}"
  4 "trusted-firmware-m":"/home/ted/projects/zephyr-based/modules/tee/tfm":"${ZEPHYR_TRUSTED_FIRMWARE_M_CMAKE_DIR}"
  5 "tfm-mcuboot":"/home/ted/projects/zephyr-based/modules/tee/tfm-mcuboot":""
  6 "cjson":"/home/ted/projects/zephyr-based/modules/lib/cjson":"${ZEPHYR_CJSON_CMAKE_DIR}"
  7 "pelion-dm":"/home/ted/projects/zephyr-based/modules/lib/pelion-dm":"/home/ted/projects/zephyr-based/modules/lib/pelion-dm/zephyr/cmake"
  8 "cddl-gen":"/home/ted/projects/zephyr-based/modules/lib/cddl-gen":"${ZEPHYR_CDDL_GEN_CMAKE_DIR}"
  9 "memfault-firmware-sdk":"/home/ted/projects/zephyr-based/modules/lib/memfault-firmware-sdk":"/home/ted/projects/zephyr-based/modules/lib/memfaul    t-firmware-sdk/ports/zephyr"
 10 "cmsis":"/home/ted/projects/zephyr-based/modules/hal/cmsis":"/home/ted/projects/zephyr-based/modules/hal/cmsis"
 11 "canopennode":"/home/ted/projects/zephyr-based/modules/lib/canopennode":"/home/ted/projects/zephyr-based/modules/lib/canopennode"
 12 "civetweb":"/home/ted/projects/zephyr-based/modules/lib/civetweb":"/home/ted/projects/zephyr-based/modules/lib/civetweb"
 13 "fatfs":"/home/ted/projects/zephyr-based/modules/fs/fatfs":"/home/ted/projects/zephyr-based/modules/fs/fatfs"
 14 "hal_nordic":"/home/ted/projects/zephyr-based/modules/hal/nordic":"${ZEPHYR_HAL_NORDIC_CMAKE_DIR}"
 15 "st":"/home/ted/projects/zephyr-based/modules/hal/st":"/home/ted/projects/zephyr-based/modules/hal/st"
 16 "libmetal":"/home/ted/projects/zephyr-based/modules/hal/libmetal":"/home/ted/projects/zephyr-based/modules/hal/libmetal"
 17 "lvgl":"/home/ted/projects/zephyr-based/modules/lib/gui/lvgl":"/home/ted/projects/zephyr-based/modules/lib/gui/lvgl"
 18 "mbedtls":"/home/ted/projects/zephyr-based/modules/crypto/mbedtls":"${ZEPHYR_MBEDTLS_CMAKE_DIR}"
 19 "mcumgr":"/home/ted/projects/zephyr-based/modules/lib/mcumgr":"/home/ted/projects/zephyr-based/modules/lib/mcumgr"
 20 "open-amp":"/home/ted/projects/zephyr-based/modules/lib/open-amp":"/home/ted/projects/zephyr-based/modules/lib/open-amp"
 21 "loramac-node":"/home/ted/projects/zephyr-based/modules/lib/loramac-node":"/home/ted/projects/zephyr-based/modules/lib/loramac-node/zephyr"
 22 "segger":"/home/ted/projects/zephyr-based/modules/debug/segger":"${ZEPHYR_SEGGER_CMAKE_DIR}"
 23 "tinycbor":"/home/ted/projects/zephyr-based/modules/lib/tinycbor":"/home/ted/projects/zephyr-based/modules/lib/tinycbor/zephyr"
 24 "tinycrypt":"/home/ted/projects/zephyr-based/modules/crypto/tinycrypt":"/home/ted/projects/zephyr-based/modules/crypto/tinycrypt"
 25 "littlefs":"/home/ted/projects/zephyr-based/modules/fs/littlefs":"/home/ted/projects/zephyr-based/modules/fs/littlefs"
 26 "mipi-sys-t":"/home/ted/projects/zephyr-based/modules/debug/mipi-sys-t":"/home/ted/projects/zephyr-based/modules/debug/mipi-sys-t"
 27 "nrf_hw_models":"/home/ted/projects/zephyr-based/modules/bsim_hw_models/nrf_hw_models":"/home/ted/projects/zephyr-based/modules/bsim_hw_models/n    rf_hw_models"
 28 "TraceRecorder":"/home/ted/projects/zephyr-based/modules/debug/TraceRecorder":"${ZEPHYR_TRACERECORDER_CMAKE_DIR}"
 29 "nrfxlib":"/home/ted/projects/zephyr-based/nrfxlib":"${ZEPHYR_NRFXLIB_CMAKE_DIR}"
 30 "connectedhomeip":"/home/ted/projects/zephyr-based/modules/lib/matter":"/home/ted/projects/zephyr-based/modules/lib/matter/config/nrfconnect/chi    p-module"
~                                                                                                                                                   
~                                                                                                                                                   
~                                                                                                                                                   
~                                                                                                                                                   
~                                                                                                                                                   
~                                                                                                                                                   
~                                                                                                                                                   
"zephyr_modules.txt" 30L, 3486C

Out of these Zephyr modules built as part of our project the hal related ones appear to be:

  • cmsis
  • hal_nordic
  • st
  • libmetal

And possibly `nrfxlib`.



./zephyr/drivers/i2c/i2c_handlers.c


3

- STEP 1 -

$ grep -nr z_vrfy_i2c_configure ./*

./zephyr/drivers/i2c/i2c_handlers.c:11:static inline int z_vrfy_i2c_configure(const struct device *dev,

 7 #include <drivers/i2c.h>
 8 #include <string.h>
 9 #include <syscall_handler.h>
10 
11 static inline int z_vrfy_i2c_configure(const struct device *dev,
12                                        uint32_t dev_config)
13 {
14         Z_OOPS(Z_SYSCALL_DRIVER_I2C(dev, configure));
15         return z_impl_i2c_configure((const struct device *)dev, dev_config);
16 }
17 #in


- STEP 2 -

./zephyr/include/drivers/i2c.h:310:static inline int z_impl_i2c_configure(const struct device *dev,

298 /**
299  * @brief Configure operation of a host controller.
300  *
301  * @param dev Pointer to the device structure for the driver instance.
302  * @param dev_config Bit-packed 32-bit value to the device runtime configuration
303  * for the I2C controller.
304  *
305  * @retval 0 If successful.
306  * @retval -EIO General input / output error, failed to configure device.
307  */
308 __syscall int i2c_configure(const struct device *dev, uint32_t dev_config);
309 
310 static inline int z_impl_i2c_configure(const struct device *dev,
311                                        uint32_t dev_config)
312 {
313         const struct i2c_driver_api *api =
314                 (const struct i2c_driver_api *)dev->api;
315 
316         return api->configure(dev, dev_config);
317 }

- STEP 3 -

./zephyr/include/drivers/i2c.h:137:__subsystem struct i2c_driver_api {

137 __subsystem struct i2c_driver_api {
138         i2c_api_configure_t configure;
139         i2c_api_full_io_t transfer;
140         i2c_api_slave_register_t slave_register;
141         i2c_api_slave_unregister_t slave_unregister;
142         i2c_api_recover_bus_t recover_bus;
143 };


. . . This code looks familiar and very similar to constructs we needed to implement for Kionix out-of-tree Zephyr driver, work cerca 2021 Q3.


[[#top|^}] Files To Review

The following files are from Zephyr, ncs, and or project `build` directory containing artifacts of the `west` directed, `ninja` based compilation:

    • [ ] ./hardware-Stage1-firmware-aws-iot-stand-alone/build/zephyr/include/generated/syscall_dispatch.c
    • [ ] ~/projects/zephyr-based$ vi ./zephyr/include/drivers/i2c.h
    • [ ]


[[#top|^}] Zephyr source i2c_nrfx_twim dot c

First reply to Devzone post 87549 points us to study some Zephyr sources in `~/projects/zephyr-based/zephyr/drivers/i2c`.


Some code line references pointing to github repo:



[[#top|^}] at_cmd_socket_thread

This work relates to study of a Zephyr reported thread named 'at_cmd_socket_thread'.

Code excerpt from './nrf/lib/at_cmd/at_cmd.c':

256                         if (errno == EHOSTDOWN) {
257                                 LOG_DBG("AT host is going down, sleeping");
258                                 atomic_set(&shutdown_mode, 1);
259                                 close(common_socket_fd);
260                                 nrf_modem_lib_shutdown_wait();
261                                 LOG_DBG("AT host available, "
262                                         "starting the thread again");



- - - top of page - - -