Difference between revisions of "Zephyr drivers"
m (→^ device_get_binding macro) |
m (Add sub-section "Devicetree guide links") |
||
| Line 685: | Line 685: | ||
<!-- --> | <!-- --> | ||
| − | === list of all DT macros === | + | === [[#top|^]] list of all DT macros === |
<pre> | <pre> | ||
| Line 883: | Line 883: | ||
| + | |||
| + | <!-- comentario --> | ||
| + | |||
| + | === [[#top|^]] Devicetree guide links === | ||
| + | |||
| + | Some important Zephyr device tree macro and use documentation links: | ||
| + | |||
| + | * https://docs.zephyrproject.org/latest/build/dts/api-usage.html#property-access | ||
| + | |||
| + | * https://docs.zephyrproject.org/latest/build/dts/api-usage.html#interrupts-properties | ||
| + | |||
| + | * https://docs.zephyrproject.org/latest/build/dts/api-usage.html#phandle-properties | ||
<!-- comentario --> | <!-- comentario --> | ||
Revision as of 23:04, 29 November 2022
Contents
- 1 ^ OVERVIEW
- 2 ^ Example Zephyr drivers
- 3 ^ Zephyr Kernel Level Device Support
- 4 ^ Understanding Zephyr SPI API
- 5 ^ Zephyr logging
- 6 ^ LPC55S69 flexcomm2 and hs_lspi pins conflict
- 7 ^ STMicro device context data structure
- 8 ^ Zephyr interrupt set up code
- 9 ^ C Preprocessor macros
- 10 ^ Zephyr device tree macros
- 11 ^ Sensors to seek for Zephyr demo exercising
^ OVERVIEW
2022 Q4 notes on Zephyr RTOS drivers, driver frameworks and driver design. Current projects include work to extend KX132-1211 Zephyr out-of-tree driver, plus work to craft an IIS2DH driver which supports in Zephyr RTOS context both I2C and SPI bus connections for this sensor.
^ Example Zephyr drivers
Example apps here offer varying amounts of insight into Zephyr RTOS' framework(s) for device driver development. Of particular interest 2022 Q4 are the ways in which developers use Zephyr device tree macros to obtain pointers to devices, in their mostly C based code, at compile time. Though not fully explained in Zephyr's extensive documentation it appears that device pointers which can be correctly passed to and used with API function device_is_ready() and macro DEVICE_DT_GET() involve pairings of macros, which must be expanded prior to these calls in order to compile correctly.
ted@localhost1:~/projects-sandbox/workspace-out-of-tree/zephyr$ grep -nr init_res ./* | grep -v reset | grep init_res ./include/zephyr/device.h:416: unsigned int init_res : 8; ./include/zephyr/net/dns_resolve.h:459:void dns_init_resolver(void); ./include/zephyr/net/dns_resolve.h:462:#define dns_init_resolver(...) ./kernel/device.c:84: dev->state->init_res = rc; ./kernel/device.c:161: return dev->state->initialized && (dev->state->init_res == 0U); ./subsys/net/ip/net_core.c:476: dns_init_resolver(); ./subsys/net/lib/dns/resolve.c:1428:void dns_init_resolver(void)
What's going on in LM77 temperature sensor Kconfig file, on line 10? Interesting Kconfig stanza contains $(dt_compat_enabled,lm77):
Zephyr sensor API routine `device_is_ready()` is prototyped in zephyr/include/zephyr/device.h. A search for `device_is_ready()` implementation gives:
ted@localhost1:~/projects-sandbox/workspace-out-of-tree/zephyr$ grep -nr z_device_is_ready ./*
./include/zephyr/device.h:782:bool z_device_is_ready(const struct device *dev);
./include/zephyr/device.h:803: return z_device_is_ready(dev);
./kernel/device.c:108: if (z_device_is_ready(dev) && (dev->name == name)) {
./kernel/device.c:114: if (z_device_is_ready(dev) && (strcmp(name, dev->name) == 0)) {
./kernel/device.c:151:bool z_device_is_ready(const struct device *dev)
The body of this API routine is:
bool z_device_is_ready(const struct device *dev)
{
/*
* if an invalid device pointer is passed as argument, this call
* reports the `device` as not ready for usage.
*/
if (dev == NULL) {
return false;
}
return dev->state->initialized && (dev->state->init_res == 0U);
}
Having some trouble, however, finding places where `init_res` and `initialized` data members of device state structure get initialized. Looked recursively in both modules and zephyr source tree. Looks like there may be one place where this assignment takes place, in `zephyr/kernel/device.c`:
ted@localhost1:~/projects-sandbox/workspace-out-of-tree/zephyr$ grep -nr init_res ./* | grep -v reset | grep init_res ./include/zephyr/device.h:416: unsigned int init_res : 8; ./include/zephyr/net/dns_resolve.h:459:void dns_init_resolver(void); ./include/zephyr/net/dns_resolve.h:462:#define dns_init_resolver(...) ./kernel/device.c:84: dev->state->init_res = rc; ./kernel/device.c:161: return dev->state->initialized && (dev->state->init_res == 0U); ./subsys/net/ip/net_core.c:476: dns_init_resolver(); ./subsys/net/lib/dns/resolve.c:1428:void dns_init_resolver(void)
Routine which iterates over and initializes all devices needing initialization prior to app code starting:
54 void z_sys_init_run_level(int32_t level)
55 {
56 static const struct init_entry *levels[] = {
57 __init_PRE_KERNEL_1_start,
58 __init_PRE_KERNEL_2_start,
59 __init_POST_KERNEL_start,
60 __init_APPLICATION_start,
61 #ifdef CONFIG_SMP
62 __init_SMP_start,
63 #endif
64 /* End marker */
65 __init_end,
66 };
67 const struct init_entry *entry;
68
69 for (entry = levels[level]; entry < levels[level+1]; entry++) {
70 const struct device *dev = entry->dev;
71 int rc = entry->init(dev);
72
73 if (dev != NULL) {
74 /* Mark device initialized. If initialization
75 * failed, record the error condition.
76 */
77 if (rc != 0) {
78 if (rc < 0) {
79 rc = -rc;
80 }
81 if (rc > UINT8_MAX) {
82 rc = UINT8_MAX;
83 }
84 dev->state->init_res = rc;
85 }
86 dev->state->initialized = true;
87 }
88 }
89 }
Sensor init priority:
ted@localhost1:~/projects-sandbox/workspace-for-nexus/zephyr$ grep -nr SENSOR_INIT_PRIORITY ./* | grep -v CONFIG_SENSOR | grep SENSOR_INIT_PRIORITY ./boards/arm/thingy52_nrf52832/board.c:33:#error BOARD_CCS_VDD_PWR_CTRL_INIT_PRIORITY must be lower than SENSOR_INIT_PRIORITY ./boards/arm/thingy52_nrf52832/Kconfig:15: BOARD_VDD_PWR_CTRL_INIT_PRIORITY, but smaller than SENSOR_INIT_PRIORITY. ./drivers/sensor/Kconfig:17:config SENSOR_INIT_PRIORITY
^ device_get_binding macro
2022-1129 New section on Zephyr `device_get_binding()` API, which Ted hopes can serve as a run time, dynamic assigner of device pointers for reintializing hung hardware or late-to-start, indeterminate start time hardware.
As of past four days 2022 Nov 26 through 29 Ted finds that Zephyr has a strong leaning to set up devices at boot time, and have device structures and pointers declared and assigned largely at compile time. The "DT_INST" family macros all seem designed to work only as static declarations, not as part of code which can refer to and assign a pointer to a device at arbitrary firmware run times. Build time errors seem to indicate that these macros expand correctly, as intended, when they appear at a global or file scoped level. That is, a macro such as DEVICE_DT_INST_DEFINE compiles correctly -- if in largely hidden ways -- when it appears outside the scope of any C function. In contrast Zephyr build tools through errors when this and related DT_ macros appear in function bodies. It looks like these macros may not be expanding inside the function bodies. There must be some basic C rules here we don't yet fully grasp . . .
In searching Zephyr 3.2.0 source tree for instances of calls to `device_get_binding()`, Ted looking for way or ways that code builds the device name parameter this API routine expects. There are many use instances of this API routine in Zephyr's `tests` directory. There is one test whose CMakeLists.txt file includes interesting notes:
"./tests/kernel/device/CMakeLists.txt" 16L, 660C
Content of this file:
1 # SPDX-License-Identifier: Apache-2.0
2
3 cmake_minimum_required(VERSION 3.20.0)
4 find_package(Zephyr REQUIRED HINTS $ENV{ZEPHYR_BASE})
5 project(device)
6
7 FILE(GLOB app_sources src/*.c)
8 target_sources(app PRIVATE ${app_sources})
9
10 # device_get_binding() compares pointers first before doing strcmp().
11 # However, enabling coverage forces -O0 to disable any compiler
12 # optimizations. There would be multiple copies of the same string,
13 # and the code pathing doing pointer comparison would not be tested
14 # at all. So add this flag to merge string constants such that
15 # the pointer comparison would be exercised.
16 zephyr_cc_option_ifdef(CONFIG_COVERAGE -fmerge-constants)
Further, there are some Zephyr code samples which also call `device_get_binding()` with a given device name. One of the I2S samples looks promising, it's at zephyr/samples/drivers/i2s/litex where in main.c there's a call to `device_get_binding("i2s_rx")`. The parameter here is double quoted, so its a hard-coded string. But what does this match? A search for this pattern from the top level Zephyr 3.2.0 source tree dir reveals:
Grep search results for `i2s_rx`, used in double quotes in call to `device_get_binding()`:
( note, blank lines added for clarity about significant search results )
ted@localhost1:~/projects-sandbox/workspace-out-of-tree/zephyr$ grep -nr i2s_rx ./*
./boards/riscv/litex_vexriscv/litex_vexriscv.dts:67:&i2s_rx {
./drivers/interrupt_controller/intc_vexriscv_litex.c:24:#define I2S_RX_IRQ DT_IRQN(DT_NODELABEL(i2s_rx))
./drivers/i2s/i2s_litex.h:35:#define I2S_RX_FIFO_ADDR DT_REG_ADDR_BY_NAME(DT_NODELABEL(i2s_rx), fifo)
./drivers/i2s/i2s_litex.h:36:#define I2S_RX_FIFO_DEPTH DT_PROP(DT_NODELABEL(i2s_rx), fifo_depth)
./drivers/i2s/i2s_litex.h:47:#define I2S_BASE_ADDR DT_REG_ADDR(DT_NODELABEL(i2s_rx)) . . . use of DT_REG_ADDR macro - TMH
./drivers/i2s/i2s_litex.h:48:#define I2S_EV_STATUS_OFFSET (DT_REG_ADDR_BY_NAME(DT_NODELABEL(i2s_rx), ev_status) \
./drivers/i2s/i2s_litex.h:50:#define I2S_EV_PENDING_OFFSET (DT_REG_ADDR_BY_NAME(DT_NODELABEL(i2s_rx), ev_pending) \
./drivers/i2s/i2s_litex.h:52:#define I2S_EV_ENABLE_OFFSET (DT_REG_ADDR_BY_NAME(DT_NODELABEL(i2s_rx), ev_enable) \
./drivers/i2s/i2s_litex.h:54:#define I2S_CONTROL_OFFSET (DT_REG_ADDR_BY_NAME(DT_NODELABEL(i2s_rx), rx_ctl) \
./drivers/i2s/i2s_litex.h:56:#define I2S_STATUS_OFFSET (DT_REG_ADDR_BY_NAME(DT_NODELABEL(i2s_rx), rx_stat) \
./drivers/i2s/i2s_litex.h:58:#define I2S_CONFIG_OFFSET (DT_REG_ADDR_BY_NAME(DT_NODELABEL(i2s_rx), rx_conf) \
./drivers/i2s/i2s_litex.c:635:#if DT_NODE_HAS_STATUS(DT_NODELABEL(i2s_rx), okay)
./drivers/i2s/i2s_mcux_sai.c:118:static void i2s_rx_stream_disable(const struct device *,
./drivers/i2s/i2s_mcux_sai.c:179:static void i2s_rx_stream_disable(const struct device *dev,
./drivers/i2s/i2s_mcux_sai.c:378: i2s_rx_stream_disable(dev, false, false);
./drivers/i2s/i2s_mcux_sai.c:389: i2s_rx_stream_disable(dev, false, false);
./drivers/i2s/i2s_mcux_sai.c:402: i2s_rx_stream_disable(dev,
./drivers/i2s/i2s_mcux_sai.c:421: i2s_rx_stream_disable(dev, true, false);
./drivers/i2s/i2s_mcux_sai.c:427: i2s_rx_stream_disable(dev, true, true);
./drivers/i2s/i2s_mcux_sai.c:814:static int i2s_rx_stream_start(const struct device *dev)
./drivers/i2s/i2s_mcux_sai.c:944: ret = i2s_rx_stream_start(dev);
./drivers/i2s/i2s_mcux_sai.c:969: i2s_rx_stream_disable(dev, true, true);
./drivers/i2s/i2s_mcux_sai.c:1006: i2s_rx_stream_disable(dev, true, true);
./dts/riscv/riscv32-litex-vexriscv.dtsi:211: i2s_rx: i2s_rx@e000a800 { <-- This result looks promising, a dts nodelabel - TMH
./samples/drivers/i2s/echo/sample.yaml:6: filter: dt_nodelabel_enabled("i2s_rxtx") or
./samples/drivers/i2s/echo/sample.yaml:7: (dt_nodelabel_enabled("i2s_rx") and dt_nodelabel_enabled("i2s_tx"))
./samples/drivers/i2s/echo/src/main.c:15:#if DT_NODE_EXISTS(DT_NODELABEL(i2s_rxtx))
./samples/drivers/i2s/echo/src/main.c:16:#define I2S_RX_NODE DT_NODELABEL(i2s_rxtx)
./samples/drivers/i2s/echo/src/main.c:19:#define I2S_RX_NODE DT_NODELABEL(i2s_rx)
.
.
.
^ Zephyr Kernel Level Device Support
Interesting code excerpt from `zephy/kernel/device.c`, this following routine is the implementation behind a wrapper like function `device_is_read()`. But this routine, and sensibly so, doesn't say anything about how a given device is initialized. It only looks at two data members of a device instance data structure:
150
151 bool z_device_is_ready(const struct device *dev)
152 {
153 /*
154 * if an invalid device pointer is passed as argument, this call
155 * reports the `device` as not ready for usage.
156 */
157 if (dev == NULL) {
158 return false;
159 }
160
161 return dev->state->initialized && (dev->state->init_res == 0U);
162 }
163
On a somewhat unrelated note, a couple of important Zephyr documents, including Zephyr device tree macros used to obtain node identifiers:
- https://docs.zephyrproject.org/latest/build/dts/dt-vs-kconfig.html Device Tree versus Kconfig, a fairly short read
^ Understanding Zephyr SPI API
To make use of Zephyr API for SPI bus, we must in part understand how each of the three parameters passed to spi_read() and spi_write() are defined. Further, when we have a sensor with which we communicate in our Zephyr based app we need to understand how parts of this sensor's data structures in the firmware relate to the SPI bus to which the sensor is connected. Our sensor driver's code which talks with the sensor via SPI must pass certain SPI bus related pointers to Zephyr's SPI Application Programmers' Interface.
Another important SPI defining resource in Zephyr RTOS is the header file spi.h#L379. This file defines the small data structure named `spi_dt_spec`. It gives us the data member names for a SPI bus peripheral, as Zephyr sees them.
2022-11-25
The best Zephyr SPI instructions we find so far are in the sample app `spi_bitbang`. The source file main.c there, sets up RX and TX buffers, and some Zephyr driver structures about these. There is an interesting design pattern in Zephyr's SPI API: receive and transmit buffer pairs can be made multiple, in two arrays of these same buffers. The SPI interface function `spi_tranceive()`, about which spi_write() and spi_read() wrap, steps through the count of write buffers and receive buffers it is passed from calling code. In this way, a careful choosing of sets of buffers permits app developers to express more complex SPI communications by defining the buffers with needed lengths, and then call the SPI API of Zephyr RTOS just once.
^ Zephyr logging
Note, in a Zephyr project or an out-of-tree driver, what we have learned here is that LOG_MODULE_REGISTER(project_name) must be called in one -- possibly the first -- of the project's source files. Any other dot c files from which developers need logging capability must include the function like macro LOG_MODULE_DECLARE().
- https://docs.zephyrproject.org/3.0.0/reference/logging/index.html#logging-in-a-module
- https://docs.zephyrproject.org/3.0.0/reference/logging/index.html#c.LOG_MODULE_DECLARE
^ LPC55S69 flexcomm2 and hs_lspi pins conflict
zephyr/boards/arm/lpcxpresso55s69/lpcxpresso55s69-pinctrl.dtsi lines 21 - 28
Note that in spite of the comment above in the dot dtsi file from NXP, SPI communications with an IIS2DH sensor work while UART2 is also in use and working - TMH
^ STMicro device context data structure
Symbol `stmdev_ctx_t` is defined in file modules/hal/st/sensor/stmemsc/iis2dh_STdC/driver/iis2dh_reg.c. On github this file as of 2022-11-18 located at https://github.com/zephyrproject-rtos/hal_st/tree/master/sensor/stmemsc/iis2dh_STdC/driver'
Data structure `stmdev_ctx_t` defined as follows:
104 /** @addtogroup Interfaces_Functions
105 * @brief This section provide a set of functions used to read and
106 * write a generic register of the device.
107 * MANDATORY: return 0 -> no Error.
108 * @{
109 *
110 */
111
112 typedef int32_t (*stmdev_write_ptr)(void *, uint8_t, const uint8_t *, uint16_t);
113 typedef int32_t (*stmdev_read_ptr)(void *, uint8_t, uint8_t *, uint16_t);
114
115 typedef struct
116 {
117 /** Component mandatory fields **/
118 stmdev_write_ptr write_reg;
119 stmdev_read_ptr read_reg;
120 /** Customizable optional pointer **/
121 void *handle;
122 } stmdev_ctx_t;
Parameter lists for the register write and register read functions are nearly the same, with exception of the third parameter. In the register write function this parameter is qualified with C `const`, as it is only expected to be read by the function using it.
With the above definition, an instance of stmdev_cts_t is created for each device with device tree compatible property of 'st_iis2dh', and is assigned in `zephyr/drivers/sensor/iis2dh/iis2dh-i2c.c` as follows:
38 stmdev_ctx_t iis2dh_i2c_ctx = {
39 .read_reg = (stmdev_read_ptr) iis2dh_i2c_read,
40 .write_reg = (stmdev_write_ptr) iis2dh_i2c_write,
41 };
42
43 int iis2dh_i2c_init(const struct device *dev)
44 {
45 struct iis2dh_data *data = dev->data;
46 const struct iis2dh_device_config *config = dev->config;
47
48 if (!device_is_ready(config->i2c.bus)) {
49 LOG_ERR("Bus device is not ready");
50 return -ENODEV;
51 }
52
53 data->ctx = &iis2dh_i2c_ctx;
54 data->ctx->handle = (void *)dev;
55
56 return 0;
57 }
58 #endif /* DT_ANY_INST_ON_BUS_STATUS_OKAY(i2c) */
The above init function is called from iis2dh.c:
232 static int iis2dh_init_interface(const struct device *dev)
233 {
234 int res;
235
236 #if DT_ANY_INST_ON_BUS_STATUS_OKAY(spi)
237 res = iis2dh_spi_init(dev);
238 if (res) {
239 return res;
240 }
241 #elif DT_ANY_INST_ON_BUS_STATUS_OKAY(i2c)
242 res = iis2dh_i2c_init(dev);
243 if (res) {
244 return res;
245 }
246 #else
247 #error "BUS MACRO NOT DEFINED IN DTS"
248 #endif
249
250 return 0;
251 }
252
253 static int iis2dh_init(const struct device *dev)
254 {
255 struct iis2dh_data *iis2dh = dev->data;
256 const struct iis2dh_device_config *cfg = dev->config;
257 uint8_t wai;
258
259 if (iis2dh_init_interface(dev)) {
260 return -EINVAL;
261 }
Pointer *dev has a member named 'data', which in turn has a member named 'ctx', which in turn gets assigned the address of a not named instance of `iis2dh_i2c_ctx`. This means that we have `dev->data->ctx->read_reg()` and `dev->data->ctx->write_reg` on successful completion of routine iis2dh_i2c_init(). This is reflected in modules/hal/st/sensor/stmemsc/iis2dh_STdC/driver/iis2dh_reg.c, in the two generalized register read and write functions:
39 /**
40 * @brief Read generic device register
41 *
42 * @param ctx read / write interface definitions(ptr)
43 * @param reg register to read
44 * @param data pointer to buffer that store the data read(ptr)
45 * @param len number of consecutive register to read
46 * @retval interface status (MANDATORY: return 0 -> no Error)
47 *
48 */
49 int32_t iis2dh_read_reg(stmdev_ctx_t *ctx, uint8_t reg, uint8_t *data,
50 uint16_t len)
51 {
52 int32_t ret;
53
54 ret = ctx->read_reg(ctx->handle, reg, data, len);
55
56 return ret;
57 }
58
59 /**
60 * @brief Write generic device register
61 *
62 * @param ctx read / write interface definitions(ptr)
63 * @param reg register to write
64 * @param data pointer to data to write in register reg(ptr)
65 * @param len number of consecutive register to write
66 * @retval interface status (MANDATORY: return 0 -> no Error)
67 *
68 */
69 int32_t iis2dh_write_reg(stmdev_ctx_t *ctx, uint8_t reg,
70 uint8_t *data,
71 uint16_t len)
72 {
73 int32_t ret;
74
75 ret = ctx->write_reg(ctx->handle, reg, data, len);
76
77 return ret;
78 }
. . .
https://docs.zephyrproject.org/latest/hardware/peripherals/i2c.html#c.i2c_burst_read_dt
^ Zephyr interrupt set up code
In Zephyr RTOS context, triggers are interrupts which are generated by sensors. Zephyr constructs a notion of "trigger types" and "trigger channels". Some pages from Zephyr 3.2.0 documentation:
- https://docs.zephyrproject.org/latest/hardware/peripherals/sensor.html#triggers
- https://docs.zephyrproject.org/latest/hardware/peripherals/sensor.html#c.sensor_trigger_type
This section created to help address a challenge we have, setting up a sensor interrupt or Zephyr "trigger" in KX132 driver. While unsure, there is suspicion that the `int_gpio` member of the sensor's `config` data structure may not be getting assigned a GPIO port at all, in an early Zephyr init level at boot time. In a diagnostic, `cfg->int_gpio.port->name` shows as "=&", which does not look like a valid port name.
KX132's config data structure includes this snippet of code:
58 uint8_t pm; 59 #ifdef CONFIG_KX132_TRIGGER 60 #warning "KX132 1211 driver - compiling gpio_dt_spec instance in struct 'kx132_device_config'" 61 // # REF https://github.com/zephyrproject-rtos/zephyr/blob/main/include/zephyr/drivers/gpio.h#L271 62 struct gpio_dt_spec int_gpio; 63 #endif /* CONFIG_KX132_TRIGGER */ 64 };
In a different sample app, iis2dh-driver-demo, we were able to set up a trigger per the code from Zephyr's `samples/basic/button` app. The early declarative elements to prepare to use a GPIO pin on the MCU, as an interrupt input line connected to a sensor, are in this sample:
127 #include <zephyr/drivers/gpio.h> // needed to provide GPIO_DT_SPEC_GET_OR Zephyr device tree macro
128
129 #define SENSOR_INT1_NODE DT_ALIAS(sensorinterrupt1)
130 #if !DT_NODE_HAS_STATUS(SENSOR_INT1_NODE, okay)
131 #error "- DEV 1108 - Could not find in device tree source any sensor interrupt type node!"
132 #endif
133 //static const struct gpio_dt_spec button = GPIO_DT_SPEC_GET_OR(SW0_NODE, gpios, {0});
134 static const struct gpio_dt_spec interrupt_line_1 = GPIO_DT_SPEC_GET_OR(SENSOR_INT1_NODE, gpios, {0});
135
136 static struct gpio_callback sensor_interrupt_1_cb_data;
Device tree overlay expresses the above referenced DTS node alias:
5 / {
6 aliases {
9 sensorinterrupt1 = &iis2dhint1;
11 };
12 };
65 / {
66 sensor_interrupts {
67 compatible = "gpio-keys";
68 iis2dhint1: iis2dh_int1 {
69 gpios = < &gpio1 9 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>;
70 };
71 /* ... other buttons ... */
72 };
73 };
In a driver use case, the interrupt line(s) or pins themselves likely won't require a DTS node alias. These GPIO pins will be expressed as values in the sensor's device tree node. The property will be one of `irq-gpios`, `drdy-gpios` and similar, depending on the given sensor's device tree bindings file. Of course, the port controlling the given pins must somewhere in device tree or DTS overlay files be enabled.
Zephyr interrupt set up code from button sample app . . .
MODULE_ID__THREAD_IIS2DH, sensor->state->init_res);
// 'button' from samples/basic/button becomes 'interrupt_line_1':
// STEP config step
if (!device_is_ready(interrupt_line_1.port)) {
printk("Error: sensor interrupt 1 port '%s' detected as not ready\n",
interrupt_line_1.port->name);
// return;
}
// STEP config step
rstatus = gpio_pin_configure_dt(&interrupt_line_1, GPIO_INPUT);
if (rstatus != 0) {
printk("Error %d: failed to configure %s pin %d\n",
rstatus, interrupt_line_1.port->name, interrupt_line_1.pin);
// return;
}
// STEP config step
rstatus = gpio_pin_interrupt_configure_dt(&interrupt_line_1,
GPIO_INT_EDGE_TO_ACTIVE);
if (rstatus != 0) {
printk("Error %d: failed to configure interrupt on %s pin %d\n",
rstatus, interrupt_line_1.port->name, interrupt_line_1.pin);
// return;
}
// STEP config step
// gpio_init_callback(&button_cb_data, button_pressed, BIT(button.pin));
// gpio_add_callback(button.port, &button_cb_data);
// printk("Set up button at %s pin %d\n", button.port->name, button.pin);
gpio_init_callback(&sensor_interrupt_1_cb_data, sensor_interrupt_1_cb, BIT(interrupt_line_1.pin));
gpio_add_callback(interrupt_line_1.port, &sensor_interrupt_1_cb_data);
printk("Set up button at %s pin %d\n", interrupt_line_1.port->name, interrupt_line_1.pin);
Interestingly this demo code gives the following port name after the GPIO based interrupt is successfully configured:
*** Booting Zephyr OS build zephyr-v3.2.0 *** - scoreboard - in setter function test val holds 0, - scoreboard - setting test val to 5, Success in init of KX132! - DEV 1028 - symbol ST_IIS2DH got assigned 'DT_N_S_soc_S_peripheral_50000000_S_spi_9f000_S_iis2dh_0' - kd_thread_iis2dh - Success finding iis2dh device, - kd_thread_iis2dh - sensor device 'iis2dh@0' is ready, - kd_thread_iis2dh - INFO: device name (Zephyr compile time setting) found to be 'iis2dh@0' - kd_thread_iis2dh - INFO: boot time Zephyr init result value holds 0, INFO: sensor interrupt 1 port 'gpio@1' detected as ready! Set up button at gpio@1 pin 9
Name `gpio@1` is definitely not equivalent or like `=&`. So QUESTION: where in the run time process, and in the source code of a given out-of-tree driver, is a valid port controller assigned to `const struct device *dev->cfg->int_gpio.port`?
In Jared Wolff's sgp40 driver there's explicit code to assign values to sensor data structure members which support an enable line. Line of interest is sgp40.c line 153. In this case the line communication is an enable line, not an interrupt, but the needed set up should be equivalent.
QUESTION: where and how is STMicro IIS2DH driver achieving the same set up for its "data ready", drdy gpio?
^ C Preprocessor macros
^ Zephyr device tree macros
Section on Zephyr device tree macros, many defined in devicetree.h. Also worth noting is Zephyr 3.2.0 notes on device drivers that depend on other devices.
Definition of DT_DRV_INST
2903 /**
2904 * @defgroup devicetree-inst Instance-based devicetree APIs
2905 * @ingroup devicetree
2906 * @{
2907 */
2908
2909 /**
2910 * @brief Node identifier for an instance of a `DT_DRV_COMPAT` compatible
2911 * @param inst instance number
2912 * @return a node identifier for the node with `DT_DRV_COMPAT` compatible and
2913 * instance number @p inst
2914 */
2915 #define DT_DRV_INST(inst) DT_INST(inst, DT_DRV_COMPAT)
Definition of DT_INST
232 /**
233 * @brief Get a node identifier for an instance of a compatible
234 *
235 * All nodes with a particular compatible property value are assigned
236 * instance numbers, which are zero-based indexes specific to that
237 * compatible. You can get a node identifier for these nodes by
238 * passing DT_INST() an instance number, @p inst, along with the
239 * lowercase-and-underscores version of the compatible, @p compat.
240 *
241 * Instance numbers have the following properties:
242 *
243 * - for each compatible, instance numbers start at 0 and are contiguous
244 * - exactly one instance number is assigned for each node with a compatible,
245 * **including disabled nodes**
246 * - enabled nodes (status property is `okay` or missing) are assigned the
247 * instance numbers starting from 0, and disabled nodes have instance
248 * numbers which are greater than those of any enabled node
249 *
250 * No other guarantees are made. In particular:
251 *
252 * - instance numbers **in no way reflect** any numbering scheme that
253 * might exist in SoC documentation, node labels or unit addresses,
254 * or properties of the /aliases node (use DT_NODELABEL() or DT_ALIAS()
255 * for those)
256 * - there **is no general guarantee** that the same node will have
257 * the same instance number between builds, even if you are building
258 * the same application again in the same build directory
259 *
260 * Example devicetree fragment:
261 *
262 * @code{.dts}
263 * serial1: serial@40001000 {
264 * compatible = "vnd,soc-serial";
265 * status = "disabled";
266 * current-speed = <9600>;
267 * ...
268 * };
269 *
270 * serial2: serial@40002000 {
271 * compatible = "vnd,soc-serial";
272 * status = "okay";
273 * current-speed = <57600>;
274 * ...
275 * };
276 *
277 * serial3: serial@40003000 {
278 * compatible = "vnd,soc-serial";
279 * current-speed = <115200>;
280 * ...
281 * };
282 * @endcode
283 *
284 * Assuming no other nodes in the devicetree have compatible
285 * `"vnd,soc-serial"`, that compatible has nodes with instance numbers
286 * 0, 1, and 2.
287 *
288 * The nodes `serial@40002000` and `serial@40003000` are both enabled, so
289 * their instance numbers are 0 and 1, but no guarantees are made
290 * regarding which node has which instance number.
291 *
292 * Since `serial@40001000` is the only disabled node, it has instance
293 * number 2, since disabled nodes are assigned the largest instance
294 * numbers. Therefore:
295 *
296 * @code{.c}
297 * // Could be 57600 or 115200. There is no way to be sure:
298 * // either serial@40002000 or serial@40003000 could
299 * // have instance number 0, so this could be the current-speed
300 * // property of either of those nodes.
301 * DT_PROP(DT_INST(0, vnd_soc_serial), current_speed)
302 *
303 * // Could be 57600 or 115200, for the same reason.
304 * // If the above expression expands to 57600, then
305 * // this expands to 115200, and vice-versa.
306 * DT_PROP(DT_INST(1, vnd_soc_serial), current_speed)
307 *
308 * // 9600, because there is only one disabled node, and
309 * // disabled nodes are "at the the end" of the instance
310 * // number "list".
311 * DT_PROP(DT_INST(2, vnd_soc_serial), current_speed)
312 * @endcode
313 *
314 * Notice how `"vnd,soc-serial"` in the devicetree becomes `vnd_soc_serial`
315 * (without quotes) in the DT_INST() arguments. (As usual, `current-speed`
316 * in the devicetree becomes `current_speed` as well.)
317 *
318 * Nodes whose `compatible` property has multiple values are assigned
319 * independent instance numbers for each compatible.
320 *
321 * @param inst instance number for compatible @p compat
322 * @param compat lowercase-and-underscores compatible, without quotes
323 * @return node identifier for the node with that instance number and
324 * compatible
325 */
326 #define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat))
^ list of all DT macros
ted@localhost1:~/projects-sandbox/workspace-out-of-tree/zephyr/include/zephyr$ grep -n DT_ devicetree.h | grep define 77:#define DT_INVALID_NODE _ 82:#define DT_ROOT DT_N 134:#define DT_PATH(...) DT_PATH_INTERNAL(__VA_ARGS__) 190:#define DT_NODELABEL(label) DT_CAT(DT_N_NODELABEL_, label) 230:#define DT_ALIAS(alias) DT_CAT(DT_N_ALIAS_, alias) 326:#define DT_INST(inst, compat) UTIL_CAT(DT_N_INST, DT_DASH(inst, compat)) 351:#define DT_PARENT(node_id) UTIL_CAT(node_id, _PARENT) 358:#define DT_INST_PARENT(inst) DT_PARENT(DT_DRV_INST(inst)) 383:#define DT_GPARENT(node_id) DT_PARENT(DT_PARENT(node_id)) 406: * #define SOC_NODE DT_NODELABEL(soc_label) 420:#define DT_CHILD(node_id, child) UTIL_CAT(node_id, DT_S_PREFIX(child)) 463:#define DT_COMPAT_GET_ANY_STATUS_OKAY(compat) \ 495:#define DT_NODE_PATH(node_id) DT_CAT(node_id, _PATH) 521:#define DT_NODE_FULL_NAME(node_id) DT_CAT(node_id, _FULL_NAME) 549:#define DT_NODE_CHILD_IDX(node_id) DT_CAT(node_id, _CHILD_IDX) 571:#define DT_SAME_NODE(node_id1, node_id2) \ 614:#define DT_PROP(node_id, prop) DT_CAT3(node_id, _P_, prop) 644:#define DT_PROP_LEN(node_id, prop) DT_CAT4(node_id, _P_, prop, _LEN) 649: * If the property is defined (as determined by DT_NODE_HAS_PROP()), 660:#define DT_PROP_LEN_OR(node_id, prop, default_value) \ 684:#define DT_PROP_HAS_IDX(node_id, prop, idx) \ 719:#define DT_PROP_HAS_NAME(node_id, prop, name) \ 744:#define DT_PROP_BY_IDX(node_id, prop, idx) \ 760:#define DT_PROP_OR(node_id, prop, default_value) \ 773:#define DT_LABEL(node_id) DT_PROP(node_id, label) __DEPRECATED_MACRO 815:#define DT_ENUM_IDX(node_id, prop) DT_CAT4(node_id, _P_, prop, _ENUM_IDX) 831:#define DT_ENUM_IDX_OR(node_id, prop, default_idx_value) \ 894:#define DT_STRING_TOKEN(node_id, prop) \ 910:#define DT_STRING_TOKEN_OR(node_id, prop, default_value) \ 971:#define DT_STRING_UPPER_TOKEN(node_id, prop) \ 988:#define DT_STRING_UPPER_TOKEN_OR(node_id, prop, default_value) \ 1039:#define DT_STRING_TOKEN_BY_IDX(node_id, prop, idx) \ 1089:#define DT_STRING_UPPER_TOKEN_BY_IDX(node_id, prop, idx) \ 1131: * #define N1 DT_NODELABEL(n1) 1145:#define DT_PROP_BY_PHANDLE_IDX(node_id, phs, idx, prop) \ 1167:#define DT_PROP_BY_PHANDLE_IDX_OR(node_id, phs, idx, prop, default_value) \ 1181:#define DT_PROP_BY_PHANDLE(node_id, ph, prop) \ 1225: * #define LED DT_NODELABEL(led) 1238:#define DT_PHA_BY_IDX(node_id, pha, idx, cell) \ 1252: * defined, so it's safe to use DT_PROP_OR() here, because that uses an 1264:#define DT_PHA_BY_IDX_OR(node_id, pha, idx, cell, default_value) \ 1274:#define DT_PHA(node_id, pha, cell) DT_PHA_BY_IDX(node_id, pha, 0, cell) 1290:#define DT_PHA_OR(node_id, pha, cell, default_value) \ 1333:#define DT_PHA_BY_NAME(node_id, pha, name, cell) \ 1346: * defined, so it's safe to use DT_PROP_OR() here, because that uses an 1357:#define DT_PHA_BY_NAME_OR(node_id, pha, name, cell, default_value) \ 1393: * #define NODE DT_NODELABEL(n) 1407:#define DT_PHANDLE_BY_NAME(node_id, pha, name) \ 1439: * #define N1 DT_NODELABEL(n1) 1459:#define DT_PHANDLE_BY_IDX(node_id, prop, idx) \ 1473:#define DT_PHANDLE(node_id, prop) DT_PHANDLE_BY_IDX(node_id, prop, 0) 1521:#define DT_NUM_RANGES(node_id) DT_CAT(node_id, _RANGES_NUM) 1575:#define DT_RANGES_HAS_IDX(node_id, idx) \ 1630:#define DT_RANGES_HAS_CHILD_BUS_FLAGS_AT_IDX(node_id, idx) \ 1670:#define DT_RANGES_CHILD_BUS_FLAGS_BY_IDX(node_id, idx) \ 1719:#define DT_RANGES_CHILD_BUS_ADDRESS_BY_IDX(node_id, idx) \ 1768:#define DT_RANGES_PARENT_BUS_ADDRESS_BY_IDX(node_id, idx) \ 1817:#define DT_RANGES_LENGTH_BY_IDX(node_id, idx) \ 1841: * #define RANGE_LENGTH(node_id, idx) DT_RANGES_LENGTH_BY_IDX(node_id, idx), 1859:#define DT_FOREACH_RANGE(node_id, fn) \ 1907:#define DT_NODE_VENDOR_BY_IDX(node_id, idx) \ 1922:#define DT_NODE_VENDOR_HAS_IDX(node_id, idx) \ 1939:#define DT_NODE_VENDOR_BY_IDX_OR(node_id, idx, default_value) \ 1951:#define DT_NODE_VENDOR_OR(node_id, default_value) \ 1971:#define DT_NUM_REGS(node_id) DT_CAT(node_id, _REG_NUM) 1984:#define DT_REG_HAS_IDX(node_id, idx) \ 1993:#define DT_REG_ADDR_BY_IDX(node_id, idx) \ 2007:#define DT_REG_SIZE_BY_IDX(node_id, idx) \ 2017:#define DT_REG_ADDR(node_id) DT_REG_ADDR_BY_IDX(node_id, 0) 2026:#define DT_REG_SIZE(node_id) DT_REG_SIZE_BY_IDX(node_id, 0) 2034:#define DT_REG_ADDR_BY_NAME(node_id, name) \ 2043:#define DT_REG_SIZE_BY_NAME(node_id, name) \ 2064:#define DT_NUM_IRQS(node_id) DT_CAT(node_id, _IRQ_NUM) 2076:#define DT_IRQ_HAS_IDX(node_id, idx) \ 2089:#define DT_IRQ_HAS_CELL_AT_IDX(node_id, idx, cell) \ 2099:#define DT_IRQ_HAS_CELL(node_id, cell) DT_IRQ_HAS_CELL_AT_IDX(node_id, 0, cell) 2110:#define DT_IRQ_HAS_NAME(node_id, name) \ 2134: * #define SERIAL DT_NODELABEL(my_serial) 2148:#define DT_IRQ_BY_IDX(node_id, idx, cell) \ 2166:#define DT_IRQ_BY_NAME(node_id, name, cell) \ 2176:#define DT_IRQ(node_id, cell) DT_IRQ_BY_IDX(node_id, 0, cell) 2188:#define DT_IRQN(node_id) DT_IRQ(node_id, irq) 2208:#define DT_CHOSEN(prop) DT_CAT(DT_CHOSEN_, prop) 2216:#define DT_HAS_CHOSEN(prop) IS_ENABLED(DT_CAT3(DT_CHOSEN_, prop, _EXISTS)) 2237:#define DT_FOREACH_NODE(fn) DT_FOREACH_HELPER(fn) 2250:#define DT_FOREACH_STATUS_OKAY_NODE(fn) DT_FOREACH_OKAY_HELPER(fn) 2277: * #define FOOBAR_AND_COMMA(node_id) DT_PROP(node_id, foobar), 2295:#define DT_FOREACH_CHILD(node_id, fn) \ 2338:#define DT_FOREACH_CHILD_SEP(node_id, fn, sep) \ 2356:#define DT_FOREACH_CHILD_VARGS(node_id, fn, ...) \ 2374:#define DT_FOREACH_CHILD_SEP_VARGS(node_id, fn, sep, ...) \ 2392:#define DT_FOREACH_CHILD_STATUS_OKAY(node_id, fn) \ 2411:#define DT_FOREACH_CHILD_STATUS_OKAY_SEP(node_id, fn, sep) \ 2433:#define DT_FOREACH_CHILD_STATUS_OKAY_VARGS(node_id, fn, ...) \ 2454:#define DT_FOREACH_CHILD_STATUS_OKAY_SEP_VARGS(node_id, fn, sep, ...) \ 2507:#define DT_FOREACH_PROP_ELEM(node_id, prop, fn) \ 2527:#define DT_FOREACH_PROP_ELEM_VARGS(node_id, prop, fn, ...) \ 2583:#define DT_FOREACH_STATUS_OKAY(compat, fn) \ 2613: * #define MY_FN(node_id, operator) DT_PROP(node_id, val) operator 2632:#define DT_FOREACH_STATUS_OKAY_VARGS(compat, fn, ...) \ 2662:#define DT_NODE_EXISTS(node_id) IS_ENABLED(DT_CAT(node_id, _EXISTS)) 2685:#define DT_NODE_HAS_STATUS(node_id, status) \ 2707:#define DT_HAS_COMPAT_STATUS_OKAY(compat) \ 2716:#define DT_NUM_INST_STATUS_OKAY(compat) \ 2747:#define DT_NODE_HAS_COMPAT(node_id, compat) \ 2764:#define DT_NODE_HAS_COMPAT_STATUS(node_id, compat, status) \ 2780:#define DT_NODE_HAS_PROP(node_id, prop) \ 2800:#define DT_PHA_HAS_CELL_AT_IDX(node_id, pha, idx, cell) \ 2813:#define DT_PHA_HAS_CELL(node_id, pha, cell) \ 2857:#define DT_BUS(node_id) DT_CAT(node_id, _BUS) 2867:#define DT_BUS_LABEL(node_id) DT_PROP(DT_BUS(node_id), label) __DEPRECATED_MACRO 2897:#define DT_ON_BUS(node_id, bus) IS_ENABLED(DT_CAT3(node_id, _BUS_, bus)) 2915:#define DT_DRV_INST(inst) DT_INST(inst, DT_DRV_COMPAT) 2926:#define DT_INST_CHILD(inst, child) \ 2943:#define DT_INST_FOREACH_CHILD(inst, fn) \ 2959:#define DT_INST_FOREACH_CHILD_SEP(inst, fn, sep) \ 2977:#define DT_INST_FOREACH_CHILD_VARGS(inst, fn, ...) \ 2994:#define DT_INST_FOREACH_CHILD_SEP_VARGS(inst, fn, sep, ...) \ 3008:#define DT_INST_FOREACH_CHILD_STATUS_OKAY(inst, fn) \ 3025:#define DT_INST_FOREACH_CHILD_STATUS_OKAY_SEP(inst, fn, sep) \ 3041:#define DT_INST_FOREACH_CHILD_STATUS_OKAY_VARGS(inst, fn, ...) \ 3059:#define DT_INST_FOREACH_CHILD_STATUS_OKAY_SEP_VARGS(inst, fn, sep, ...) \ 3068:#define DT_INST_ENUM_IDX(inst, prop) \ 3079:#define DT_INST_ENUM_IDX_OR(inst, prop, default_idx_value) \ 3088:#define DT_INST_PROP(inst, prop) DT_PROP(DT_DRV_INST(inst), prop) 3096:#define DT_INST_PROP_LEN(inst, prop) DT_PROP_LEN(DT_DRV_INST(inst), prop) 3107:#define DT_INST_PROP_HAS_IDX(inst, prop, idx) \ 3118:#define DT_INST_PROP_HAS_NAME(inst, prop, name) \ 3128:#define DT_INST_PROP_BY_IDX(inst, prop, idx) \ 3138:#define DT_INST_PROP_OR(inst, prop, default_value) \ 3147:#define DT_INST_LABEL(inst) DT_INST_PROP(inst, label) __DEPRECATED_MACRO 3158:#define DT_INST_STRING_TOKEN(inst, prop) \ 3168:#define DT_INST_STRING_UPPER_TOKEN(inst, prop) \ 3178:#define DT_INST_STRING_TOKEN_BY_IDX(inst, prop, idx) \ 3188:#define DT_INST_STRING_UPPER_TOKEN_BY_IDX(inst, prop, idx) \ 3199:#define DT_INST_PROP_BY_PHANDLE(inst, ph, prop) \ 3213:#define DT_INST_PROP_BY_PHANDLE_IDX(inst, phs, idx, prop) \ 3224:#define DT_INST_PHA_BY_IDX(inst, pha, idx, cell) \ 3236:#define DT_INST_PHA_BY_IDX_OR(inst, pha, idx, cell, default_value) \ 3247:#define DT_INST_PHA(inst, pha, cell) DT_INST_PHA_BY_IDX(inst, pha, 0, cell) 3257:#define DT_INST_PHA_OR(inst, pha, cell, default_value) \ 3269:#define DT_INST_PHA_BY_NAME(inst, pha, name, cell) \ 3281:#define DT_INST_PHA_BY_NAME_OR(inst, pha, name, cell, default_value) \ 3292:#define DT_INST_PHANDLE_BY_NAME(inst, pha, name) \ 3304:#define DT_INST_PHANDLE_BY_IDX(inst, prop, idx) \ 3315:#define DT_INST_PHANDLE(inst, prop) DT_INST_PHANDLE_BY_IDX(inst, prop, 0) 3324:#define DT_INST_REG_HAS_IDX(inst, idx) DT_REG_HAS_IDX(DT_DRV_INST(inst), idx) 3332:#define DT_INST_REG_ADDR_BY_IDX(inst, idx) DT_REG_ADDR_BY_IDX(DT_DRV_INST(inst), idx) 3340:#define DT_INST_REG_SIZE_BY_IDX(inst, idx) \ 3349:#define DT_INST_REG_ADDR_BY_NAME(inst, name) \ 3358:#define DT_INST_REG_SIZE_BY_NAME(inst, name) \ 3366:#define DT_INST_REG_ADDR(inst) DT_INST_REG_ADDR_BY_IDX(inst, 0) 3373:#define DT_INST_REG_SIZE(inst) DT_INST_REG_SIZE_BY_IDX(inst, 0) 3382:#define DT_INST_IRQ_BY_IDX(inst, idx, cell) \ 3392:#define DT_INST_IRQ_BY_NAME(inst, name, cell) \ 3401:#define DT_INST_IRQ(inst, cell) DT_INST_IRQ_BY_IDX(inst, 0, cell) 3408:#define DT_INST_IRQN(inst) DT_INST_IRQ(inst, irq) 3415:#define DT_INST_BUS(inst) DT_BUS(DT_DRV_INST(inst)) 3425:#define DT_INST_BUS_LABEL(inst) DT_BUS_LABEL(DT_DRV_INST(inst)) __DEPRECATED_MACRO 3434:#define DT_INST_ON_BUS(inst, bus) DT_ON_BUS(DT_DRV_INST(inst), bus) 3445:#define DT_INST_STRING_TOKEN_OR(inst, name, default_value) \ 3456:#define DT_INST_STRING_UPPER_TOKEN_OR(inst, name, default_value) \ 3482: * #define DT_DRV_COMPAT vnd_some_sensor 3491:#define DT_ANY_INST_ON_BUS_STATUS_OKAY(bus) \ 3526: * #define DT_DRV_COMPAT vnd_device 3527: * #define MY_FN(inst) DT_INST_PROP(inst, foobar), 3559:#define DT_INST_FOREACH_STATUS_OKAY(fn) \ 3576:#define DT_INST_FOREACH_STATUS_OKAY_VARGS(fn, ...) \ 3592:#define DT_INST_FOREACH_PROP_ELEM(inst, prop, fn) \ 3609:#define DT_INST_FOREACH_PROP_ELEM_VARGS(inst, prop, fn, ...) \ 3618:#define DT_INST_NODE_HAS_PROP(inst, prop) \ 3631:#define DT_INST_PHA_HAS_CELL_AT_IDX(inst, pha, idx, cell) \ 3643:#define DT_INST_PHA_HAS_CELL(inst, pha, cell) \ 3653:#define DT_INST_IRQ_HAS_IDX(inst, idx) DT_IRQ_HAS_IDX(DT_DRV_INST(inst), idx) 3663:#define DT_INST_IRQ_HAS_CELL_AT_IDX(inst, idx, cell) \ 3673:#define DT_INST_IRQ_HAS_CELL(inst, cell) \ 3682:#define DT_INST_IRQ_HAS_NAME(inst, name) \ 3691:#define DT_PATH_INTERNAL(...) \ 3698:#define DT_S_PREFIX(name) _S_##name 3714:#define DT_CAT(a1, a2) a1 ## a2 3716:#define DT_CAT3(a1, a2, a3) a1 ## a2 ## a3 3718:#define DT_CAT4(a1, a2, a3, a4) a1 ## a2 ## a3 ## a4 3720:#define DT_CAT5(a1, a2, a3, a4, a5) a1 ## a2 ## a3 ## a4 ## a5 3722:#define DT_CAT6(a1, a2, a3, a4, a5, a6) a1 ## a2 ## a3 ## a4 ## a5 ## a6 3724:#define DT_CAT7(a1, a2, a3, a4, a5, a6, a7) \ 3727:#define DT_CAT8(a1, a2, a3, a4, a5, a6, a7, a8) \ 3730: * If you need to define a bigger DT_CATN(), do so here. Don't leave 3735:#define DT_DASH(...) MACRO_MAP_CAT(DT_DASH_PREFIX, __VA_ARGS__) 3737:#define DT_DASH_PREFIX(name) _##name 3739:#define DT_NODE_HAS_STATUS_INTERNAL(node_id, status) \ 3742:#define DT_COMPAT_ON_BUS_INTERNAL(compat, bus) \
^ Devicetree guide links
Some important Zephyr device tree macro and use documentation links:
^ Sensors to seek for Zephyr demo exercising
[ ] MCP9808 I2C based temperature sensor, datasheet, long lead times at Mouser
