Difference between revisions of "Spi device tree source code"
From Wiki at Neela Nurseries
m |
m (Add section above dts excerpts to better position TOC within page.) |
||
| Line 4: | Line 4: | ||
| + | |||
| + | == SPI dts examples == | ||
In Zephyr RTOS' supported board dts files we find SPI peripherals defined for several boards. Here are excerpts | In Zephyr RTOS' supported board dts files we find SPI peripherals defined for several boards. Here are excerpts | ||
Revision as of 23:49, 11 August 2022
2022-08-11 Thursday
Notes on SPI device tree source, with goal to add SPI device to modified RPi Pico DTS files, which build firmware to run on Sparkfun DEV-18288 board.
Contents
SPI dts examples
In Zephyr RTOS' supported board dts files we find SPI peripherals defined for several boards. Here are excerpts
Excerpt 1 - zephyr/boards/arm/sparkfun_thing_plus_nrf9160/sparkfun_thing_plus_nrf9160_common.dts
142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 |
&spi3 {
compatible = "nordic,nrf-spim";
status = "okay";
cs-gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&spi3_default>;
pinctrl-1 = <&spi3_sleep>;
pinctrl-names = "default", "sleep";
w25q32jv: w25q32jv@0 {
compatible = "jedec,spi-nor";
label = "W25Q32JV";
reg = <0>;
spi-max-frequency = <40000000>;
wp-gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
hold-gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
size = <0x2000000>;
has-dpd;
t-enter-dpd = <3000>;
t-exit-dpd = <30000>;
jedec-id = [ ef 40 16 ];
};
};
|
a |
81 spi3_default: spi3_default {
82 group1 {
83 psels = <NRF_PSEL(SPIM_SCK, 0, 11)>,
84 <NRF_PSEL(SPIM_MOSI, 0, 9)>,
85 <NRF_PSEL(SPIM_MISO, 0, 28)>;
86 };
87 };
88
89 spi3_sleep: spi3_sleep {
90 group1 {
91 psels = <NRF_PSEL(SPIM_SCK, 0, 11)>,
92 <NRF_PSEL(SPIM_MOSI, 0, 9)>,
93 <NRF_PSEL(SPIM_MISO, 0, 28)>;
94 low-power-enable;
95 };
96 };
|
^ edit point dts excerpt 2
Excerpt 2 - zephyr/boards/arm/96b_carbon_nrf51/96b_carbon_nrf51.dts and 96b_carbon_nrf51-pinctrl.dtsi
47 48 49 50 |
&spi1 {
compatible = "nordic,nrf-spis";
status = "okay";
def-char = <0x00>;
pinctrl-0 = <&spi1_default>;
pinctrl-names = "default";
bt-hci@0 {
compatible = "zephyr,bt-hci-spi-slave";
reg = <0>;
irq-gpios = <&gpio0 28 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>;
};
};
|
37 38 39 |
spi1_default: spi1_default {
group1 {
psels = <NRF_PSEL(SPIS_SCK, 0, 7)>,
<NRF_PSEL(SPIS_MOSI, 0, 0)>,
<NRF_PSEL(SPIS_MISO, 0, 30)>,
<NRF_PSEL(SPIS_CSN, 0, 25)>;
};
};
|
^ edit point dts excerpt 3
Excerpt 3 - <i>
114 115 116 |
&spi1 {
pinctrl-0 = <&spi1_sck_pg2 &spi1_miso_pg3 &spi1_mosi_pg4>;
pinctrl-names = "default";
cs-gpios = <&gpiog 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>;
status = "okay";
spbtle-rf@0 {
compatible = "zephyr,bt-hci-spi";
reg = <0>;
irq-gpios = <&gpiog 6 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>;
reset-gpios = <&gpiog 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
spi-max-frequency = <2000000>;
label = "SPBTLE-RF";
};
};
|
|
|
^ edit point dts excerpt 4
<i>Excerpt 4 - <i>
|
|
|
|
|
^ edit point dts excerpt 5
<i>Excerpt 5 - <i>
|
|
|
|
|
^ YAML device bindings files
To support a typical development kit or custom board with multiple peripherals we need a device bindings file comparable to this ... bindings file:
- ~/projects-sandbox/workspace-for-rpi/zephyr/boards/arm/nrf9160dk_nrf9160/nrf9160dk_nrf9160.yaml
identifier: nrf9160dk_nrf9160 name: nRF9160-DK-NRF9160 type: mcu arch: arm toolchain: - gnuarmemb - xtools - zephyr ram: 88 flash: 256 supported: - arduino_gpio - arduino_i2c - gpio - i2c - pwm - spi - watchdog - counter
