Difference between revisions of "Current debugging"

From Wiki at Neela Nurseries
Jump to: navigation, search
m (^ Device Tree syntax and Undocumented DTS)
m (C preprocessor macros, macro stringification)
Line 100: Line 100:
 
"./boards/arm/nrf9160dk_nrf9160/nrf52840_reset.c" 67L, 1609C  
 
"./boards/arm/nrf9160dk_nrf9160/nrf52840_reset.c" 67L, 1609C  
 
</pre>
 
</pre>
 +
 
<!-- comentario -->
 
<!-- comentario -->
 +
 +
C preprocessor macros, macro stringification . . .
 +
 +
*  https://home.cs.colorado.edu/~main/cs1300/doc/gnu/cpp_1.html

Revision as of 19:35, 11 November 2022

2022-11-05 SAT

[00:00:00.009,000] <err> IIS2DH: iis2dh@18: device ������rF����� is not ready
[00:00:00.017,000] <err> IIS2DH: Failed to initialize interrupts
*** Booting Zephyr OS build zephyr-v3.2.0  ***
- scoreboard - in setter function test val holds 0,
- scoreboard - setting test val to  5,
- DEV 1028 - symbol ST_IIS2DH got assigned 'DT_N_S_soc_S_peripheral_50000000_S_flexcomm_8a000_S_iis2dh_18'
- kd_thread_iis2dh - Success finding iis2dh device,
- kd_thread_iis2dh - WARNING - sensor device 'iis2dh@18' is not ready!
- kd_thread_iis2dh - INFO:  device name (Zephyr compile time setting) found to be 'iis2dh@18'
- kd_thread_iis2dh - INFO:  boot time Zephyr init result value holds 5,
- DEV 1101 - WHO_AM_I register 0x0F holds 0x33
- DEV 1101 - config register 0x22 holds 0x10
- FIFO control reg holds 0x4f
- updating this value to set watermark at 16 data entries . . .
- write_register() returns status of 0,./tests/subsys/pm/device_power_domains/src/main.c:14:	const struct device *const reg_0 = DEVICE_DT_GET(DT_NODELABEL(test_reg_0));
./tests/subsys/pm/device_power_domains/src/main.c:15:	const struct device *const reg_1 = DEVICE_DT_GET(DT_NODELABEL(test_reg_1));
./tests/subsys/pm/device_power_domains/src/main.c:16:	const struct device *const reg_chained = DEVICE_DT_GET(DT_NODELABEL(test_reg_chained));

- following update, FIFO control reg holds 0x4f
- updating FIFO ctrl register to enable FIFO mode . . .
- reading back vale . . .
- FIFO ctrl register now holds 0x4F.
- kd_thread_iis2dh - unconditionally attempting to configure data ready (drdy-gpios) interrupt,
Waiting for triggers
- whoami register, ODR register, and ctrl reg 5 hold 0x33, 0x57, 0x40
- whoami register, ODR register, and ctrl reg 5 hold 0x33, 0x57, 0x40
- whoami register, ODR register, and ctrl reg 5 hold 0x33, 0x57, 0x40


^ Device Tree syntax and Undocumented DTS


Examples from Zephyr 3.2.0 of device structure pointer assignments:

./tests/subsys/pm/device_power_domains/src/main.c:14:	const struct device *const reg_0 = DEVICE_DT_GET(DT_NODELABEL(test_reg_0));
./tests/subsys/pm/device_power_domains/src/main.c:15:	const struct device *const reg_1 = DEVICE_DT_GET(DT_NODELABEL(test_reg_1));
./tests/subsys/pm/device_power_domains/src/main.c:16:	const struct device *const reg_chained = DEVICE_DT_GET(DT_NODELABEL(test_reg_chained));


Excerpt from Nordic sample source code:

  1 /*
  2  * Copyright (c) 2019 Nordic Semiconductor ASA.
  3  *
  4  * SPDX-License-Identifier: Apache-2.0
  5  */
  6 
  7 #include <zephyr/drivers/gpio.h>
  8 #include <zephyr/drivers/uart.h>
  9 #include <zephyr/device.h>
 10 #include <zephyr/devicetree.h>
 11 
 12 #define RESET_NODE DT_NODELABEL(nrf52840_reset)
 13 
 14 #if DT_NODE_HAS_STATUS(RESET_NODE, okay)
 15 
 16 #define RESET_GPIO_CTRL  DT_GPIO_CTLR(RESET_NODE, gpios)
 17 #define RESET_GPIO_PIN   DT_GPIO_PIN(RESET_NODE, gpios)
 18 #define RESET_GPIO_FLAGS DT_GPIO_FLAGS(RESET_NODE, gpios)
 19 
 20 int bt_hci_transport_setup(const struct device *h4)
 21 {
 22         int err;
 23         char c;
 24         const struct device *const port = DEVICE_DT_GET(RESET_GPIO_CTRL);
 25 
 26         if (!device_is_ready(port)) {
 27                 return -EIO;
 28         }
 29 
 30         /* Configure pin as output and initialize it to inactive state. */
 31         err = gpio_pin_configure(port, RESET_GPIO_PIN,
 32                                  RESET_GPIO_FLAGS | GPIO_OUTPUT_INACTIVE);
 33         if (err) {
 34                 return err;
 35         }
 36 
 37         /* Reset the nRF52840 and let it wait until the pin is inactive again
 38          * before running to main to ensure that it won't send any data until
 39          * the H4 device is setup and ready to receive.
 40          */
 41         err = gpio_pin_set(port, RESET_GPIO_PIN, 1);
 42         if (err) {
 43                 return err;
 44         }
 45 
 46         /* Wait for the nRF52840 peripheral to stop sending data.
"./boards/arm/nrf9160dk_nrf9160/nrf52840_reset.c" 67L, 1609C 


C preprocessor macros, macro stringification . . .